Self hosting

Introduction

When you have a(n old) computer lying around, and you have cheap electricity and a good internet connection, self hosting might be a good option for you.

Why would you choose selfhosting?

Downsides

Some possible downsides of choosing to host at home could be:

Your mileage may vary, go and check each of these points, and see if selfhosting is the right choice for you. Try and calculate your power consumption and see if your electricity cost is not too expensive.

For me, the upsides outweighed the downsides, which is why I chose to host at home. But, this differs with each person and scenario. Go and research what your exact situation is, before trying anything. Otherwise you'll have to face some bad surprises.

Hardware

What kind of hardware should you choose?

If you pay your own electricity bill, power consumption is a big factor. Most old laptop computers are ideal in the sense that they don't use a lot of power, and if the battery still works, you have a built-in UPS! The bad thing is, most old laptop computers aren't that powerful, and they lack in upgradability. (you shouldn't really be using anything older than 2006, and I recommend at least a performance equivalant of a Core 2 CPU)

If you can find an energy efficient desktop (under 100W), that is a great option. They are pretty upgradable and they don't use a lot of power. They can also be pretty cheap, but old laptops are usually cheaper. If you can afford new hardware, and are willing to build a PC, you can find really power effecient CPU/motherboard combos, and they can be cheap, for example the Celeron J3060. I recommend a low wattage power supply or an effecient one for these kinds of builds. Pico PSUs are pretty tiny and efficient solutions in these builds.

Of course, if you don't pay your electricity bill or cost is not a problem for you, you can use just about any old desktop (as long as it's not from the 90's, I recommend at least a Core 2 chip again, or an Athlon 64 X2).

Usecases

Of course, hardware choices depend on the usecase. The above recommendations I gave you work fine for e-mail server, webserver and fileserver types of applications, but they will struggle to transcode video if you are going to host a media server. You'll need a faster CPU, but also a faster GPU. As an example, the Athlon 200GE or 3000G are good and efficient choices for these builds. They are decent CPUs, but also have a built in GPU that will transcode video just fine.

If you need a lot of storage, go for a case with a lot of mounts for hard drives, this way you can easily mount multiple hard drives. Pros of multiple hard drives are redundancy and speed. Cons could be that they create more heat and noise. You can't use a laptop if you want multiple drives, except if you use a hard drive caddy for the CD/DVD drive bay. Some business laptops even support RAID 1 (redundancy) and RAID 0 (speed and more storage, but you lose your files if one hard drive breaks) this way.

Getting started

Installing Debian

Once you have the machine, you can install the OS. I recommend Debian, as all of the guides on this website are Debian specific. Debian just werks as a server OS.

You'll need to burn a Debian install image onto a USB flash drive or a CD. You can download the image here, and you can also find information on how to burn the image onto a USB flash drive or CD there.

While installing Debian, do not install any desktop environment. But install an SSH server when you get the chance. Also leave webserver unchecked, even if you want to use it as a webserver. You'll have a chance to install this later.

Port forwaring

Every time you are going to set up a new server program, you need to forward a port corresponding to that program. For example, HTTP is port 80, HTTPS is 443, etc. You need to set this up on your router's NAT settings (sometimes just called port forwarding, this differs per router). These steps differ for each router. Refer to your routers manual. A simple command to see what your servers IP address is, is to run ifconfig on your server. This shows a lot of network info, but it will also show your local IP address needed for port forwarding.

Basic ports:

Static or dynamic IP address

If you want to host your server at home, make sure you have a static IP address, or you can change your dynamic IP address to a static one. Refer to your router settings, some ISPs will have options on this here. If you can't find anything on this, get in touch with your ISP.

Once you've made sure you have a static IP address, you can find out what the IP address is with various websites. You can use a search engine to easily find this out. Write this down as you'll need it later.

Once you're done, you can pretty much follow every guide on this website, the only difference is that you'll need to forward the ports you'll be using for the server.

Finding the ports you'll need to forward

If you need to know what port you'll need to forward, there's a command for that. Just type netstat -tulpn in your servers command line. If you want to see the name of the programs, you need to run it as a root user. You can do this by putting sudo before the command.

Local Address                    State       PID/Program name
0.0.0.0:25                       LISTEN      887/master
0.0.0.0:1883                     LISTEN      22452/mosquitto
0.0.0.0:445                      LISTEN      798/smbd
0.0.0.0:993                      LISTEN      381/dovecot
127.0.0.1:3306                   LISTEN      560/mysqld
0.0.0.0:587                      LISTEN      887/master
0.0.0.0:139                      LISTEN      798/smbd
127.0.1.1:12301                  LISTEN      412/opendkim
0.0.0.0:143                      LISTEN      381/dovecot
0.0.0.0:465                      LISTEN      887/master
0.0.0.0:22                       LISTEN      472/sshd
:::25                            LISTEN      887/master
:::443                           LISTEN      1769/apache2
:::1883                          LISTEN      22452/mosquitto
:::445                           LISTEN      798/smbd

Example output

In this example, if you need to find the port number from dovecot, you can look for it in the Program name column. Then you can see in the local address column that the reported local address is 0.0.0.0:993. You need to look for the part after the semicolon. In this case it's 993. So you'll need to forward port 993.

Next: Connect Your Domain and Server

Written by hiddej